285/40 R22

What size is 285/40 R22?

285/40 R22 has an overall diameter of about 30.98 in, a section width of 11.22 in and a sidewall height of 4.49 in. It turns roughly 651 times per mile. Below are the exact figures plus plus/minus sizes that stay within the selected diameter tolerance.

Geometric comparison

31x10.50 R15 stays within the configured tolerance for 285/40 R22: +0.1% diameter and +0.1% speedometer effect.

Geometric comparison
Metric This size: 285/40 R22 Alternative: 31x10.50 R15 Difference Verdict
Overall diameter 30.98 in 31.00 in +0.1% Within tolerance
Section width 11.22 in 10.50 in -0.72 in Computed difference
Sidewall height 4.49 in 8.00 in +3.51 in Computed difference
Circumference 97.32 in 97.39 in +0.1% Within tolerance
Speedo 0.0% +0.1% +0.1% Within tolerance

Seasonal check

Winter tire rules coming up?

Check tread depth, markings and local winter requirements before the first cold spell instead of waiting for the appointment rush.

Open winter tire guide

What this geometry means

285/40 R22 has a low-profile proportion. The marking combines nominal section width 11.22 in, sidewall ratio 40% and rim diameter 22 inches. One sidewall is 4.49 in; both sidewalls make up 29% of the 30.98 in overall diameter, while the rim makes up 71%.

The closest diameter entry is 31x10.50 R15 at +0.1%. Relative to 285/40 R22, it changes nominal section width by -0.72 in, each sidewall by +3.51 in and radius by +0.01 in.

At the nominal 97.32 in circumference, 1,000 rotations cover 2.47 km (1.54 mi); the inverse rates are 405/km and 651/mi.

Width endpoints in that set are 245/65 R18 (-1.57 in) and 285/60 R18 (+0.00 in) relative to 285/40 R22.

Curated alternatives: 12 sizes, spanning -1.8% to +1.6% in nominal diameter versus 285/40 R22.

Section-width mix versus 285/40 R22: 10 narrower, 2 equal-width and 0 wider entries.

This is a nominal geometry comparison only. Vehicle clearance, wheel width and offset, load and speed ratings, and manufacturer approval still require separate checks.

Specification

Specification
Overall diameter 30.98 in
Section width 11.22 in
Sidewall height 4.49 in
Circumference 97.32 in
Revolutions 405 /km · 651 /mi

In-tolerance sizes

Alternative sizes that stay within the selected diameter tolerance:

In-tolerance sizes
Size Diameter Speedo Verdict
31x10.50 R15 +0.1% +0.1% ✓ OK
31x10.50 R16 +0.1% +0.1% ✓ OK
275/55 R19 -0.2% -0.2% ✓ OK
275/45 R21 -0.7% -0.7% ✓ OK
285/50 R20 +0.8% +0.8% ✓ OK
265/70 R16 -1.2% -1.2% ✓ OK
265/65 R17 -1.3% -1.3% ✓ OK
245/65 R18 -1.4% -1.4% ✓ OK
265/60 R18 -1.5% -1.5% ✓ OK
245/70 R17 -1.5% -1.5% ✓ OK
285/60 R18 +1.6% +1.6% ✓ OK
265/50 R20 -1.8% -1.8% ✓ OK

Compare sizes

Looks valid
Looks valid
Units
Editorial preset

These are TireFitLab editorial diameter-screening presets. Regional names choose a preset, not a national legal limit, ETRTO rule or vehicle approval. The AWD preset does not establish an allowable drivetrain mismatch. Use the exact vehicle and tyre manufacturer instructions; nominal geometry alone cannot approve fitment.

Not recommendedWithin tolerance · Diameter +0.1% (+0.02 in) · US preset (±3%)
  • Not recommended · This rating covers tire geometry only, not vehicle compatibility.
  • Diameter +0.1% · Ride-height change +0.01 in.
  • Speedometer reads low · 60 mph → 60.0 mph.
  • Sidewall +3.51 in · Width -0.72 in.
Diameter+0.1%+0.02 in
Speedo @ 60+0.1%60 mph → 60.0 mph
Sidewall+3.51 inWidth -0.72 in
Ride-height change+0.01 inDiameter ÷ 2
How this result is calculated

Computed from nominal tire-size geometry: diameter, circumference and speedometer error. It does not check vehicle placard approval, load/speed rating, rim-width range, wheel-arch, suspension or brake clearance.

Methodology

Before fitting

  • Check the vehicle placard and owner’s manual first.
  • Match or exceed the required load index and speed rating.
  • Confirm rim-width range, bolt pattern, hub bore, offset and fasteners.
  • Inspect wheel-arch, suspension and brake clearance under real vehicle load.
  • Check TPMS, cold pressure and local roadworthiness rules.
Diameter
30.98 in 31.00 in+0.02 in
Sidewall
4.49 in 8.00 in+3.51 in
Width
11.22 in 10.50 in-0.72 in
Circumference
97.32 in 97.39 in+0.1%
Revs / mile
651 651
Speedo @ 60
60 mph 60.0 mph+0.1%
Ride-height change
0.00 in +0.01 in
True distance per 100 indicated
100 mi 100.1 mi+0.1%
Δ⌀ +0.02 inΔ↔ -0.72 in
  • Current — 285/40 R22
  • New — 31x10.50 R15
  • Grounded to the road: the axle rises +0.01 in.

Tires and wheels in one comparison

Result report

285/40 R22 31x10.50 R15 · Not recommended · Within tolerance

Copy/print uses this page state only; TireFitLab does not create an account or store a server-side report.

Embed or cite this result
Open embed preview

Geometric estimate. Always verify physical clearance (arches, suspension, brakes) before fitting.

In-tolerance alternative sizes

In-tolerance alternative sizes
SizeDiameterSpeedo @ 100Use this
−1″ 275/45R21-0.7%-0.7%
OE 285/40R22+0.0%+0.0%
+1″ 295/35R23+0.5%+0.5%
+2″ 285/35R24+2.8%+2.8%

More tools

Last reviewed: 2026-09-04